Wet & Stick self adhesive paper drywall tape

Product Information

Finishing Outside Corners: Use broad knife to apply the joint compound over the corner bead flange for the outside corners. The first coat should be approximately 6" wide, and the second coat 6"- 10" wide applied on each side of corner. Make sure you don’t remove all of the joint compound from the surface as you smooth it out. Joint tape needs a base layer of joint compound to adhere to the drywall. Just try to get rid of lumps and bumps in the joint compound. Fold the tape in half and along its entire length ensuring it is facing the right way up if there is one; some paper joint tapes feature a printed side which is designed to sit against the plasterboard. After the first coat is dry and before applying the next coat, remove any large lumps or bumps by drawing your taping knife along the

Paper joint tape is a strong kraft tape designed for using with jointing compounds to reinforce and strengthen drywall joints and corners. Retains strength when wet, with tapered edges for invisible seams and strong crease in centre for an effective fold. A second layer of jointing compound can then be applied to cover the entire surface of the tape. Depending on the type of compound you have used, you may have to wait until the first layer is dry (from 6 hours to several days) before applying your second coat. Alternatively, it may be recommended that you apply this coat while the first is still wet. Make sure to follow the manufacturer's instructions at all times. Basically, for plasterboard joining you’re looking at using either scrim tape, or jointing tape. There are good reasons why either of these can be your perfect choice, depending on the circumstances, and of course there are often ways around it if you need to use the other. Let’s look at the difference between the two. a product I'd recommend for any normal drywall installations or repairs. How drywall tape is designed... Finishing Inside Corners: Apply compound to both sides of corner. Crease easy paper joint tape and embed. Apply a thin coat on both sides of tape. When dry, apply a second coat to one side only. Let dry, then finish the other side. When dry, sand until smooth.Allow the preceding coat to dry and apply another thin coat, feathering out to a total width of about 8" on each side. Apply final coat to nail heads. Apply a layer of joint compound on top of the seam you want to tape over. [2] X Expert Source James Mansfield With such a specific purpose, you need to have the right circumstances to use this tape – there’s little point using it on a flat joint due to the two strips of thin steel embedded into the trim. This is what helps to create a crisp, clean finish on external corners and ensures a sharp line on all angles. It’s the perfect solution for areas where rigid angle beads aren’t suitable, so if you’re looking for a simple way to tidy up angles and external edges with minimal fuss, metal angle tape could be the option for you.

Getting the right materials for any job is vital. Fortunately these days it’s not hard to find just the right quality product, designed specifically for the task in hand. ItemImage": "//sherwin.scene7.com/is/image/sw/paint_template-1?layer=comp&wid=250&fmt=jpeg&qlt=92%2c0&op_sharpen=0&resMode=sharp2&op_usm=0.0%2c0.0%2c0%2c0&iccEmbed=0&printRes=150&_tparam_layer_1_src=sw/SW08100297", So, in summary, the professionals have their own preferences and workarounds. But if you’re new to this kind of job, it’s generally worth using scrim tape for a flat surface and joint tape for an angle. Use a jointing knife or scraper to apply some gentle pressure to the jointing tape to release any excess compound or air bubbles.

ItemThumbnailImage": "//sherwin.scene7.com/is/image/sw/paint_template-1?layer=comp&wid=250&fmt=jpeg&qlt=92%2c0&op_sharpen=0&resMode=sharp2&op_usm=0.0%2c0.0%2c0%2c0&iccEmbed=0&printRes=150&_tparam_layer_1_src=sw/SW08100297", Remember that, although you can fold scrim tape, and it can sometimes be perfect for internal joints, for angles it’s usually not going to give you the same crisp edge you’d get from a pre-creased jointing tape. ItemImage467": "//sherwin.scene7.com/is/image/sw/paint_template-1?layer=comp&wid=250&fmt=jpeg&qlt=92%2c0&op_sharpen=0&resMode=sharp2&op_usm=0.0%2c0.0%2c0%2c0&iccEmbed=0&printRes=150&_tparam_layer_1_src=sw/SW08100297", Last but by no means least, we have metal angle tape. Perhaps the least well-known plasterboard tape variety, this option is specifically designed for external corner joints and unique angles like those around bay windows for example.