Clearwater CH0018 Lay-Z-Spa Chemical Starter Kit for Hot Tub and Spa Water Treatment (Includes Chlorine, pH Minus, pH Plus, Foam Remover and Test Strips)

Product Information

Clearwater Foam Remover is designed to control and prevent foaming in your hot tub, which is typically caused by the reaction of water with shampoos, deodorants and natural body oils present on the user. Clearwater pH Plus , also known as ‘pH increaser’ is the best way to increase pH levels that have dropped below the recommended level. To avoid skin discomforts and enable the chlorine in your spa to work effectively, it’s vital that acidity is monitored and controlled. The recommended pH balance of spa water is between 7.2 and 7.6. Clearwater Clarifier contains flocculants which bind small particles of debris and algae together so that your Lay-Z-Spa filtration system can adequately remove them, resulting in clean and sparkly water. This is a very effective way of preventing your spa water from looking dull and cloudy, due to the build-up of dead algae and debris that is too small to be trapped by your filter. Even if you have treated your spa for algae using Clearwater Algaecide, it is recommended that you use the Water Clarifier to remove any residual debris.

Chlorine demand of water too high at start up, after holidays or due to excess contamination or neglect The award-winning Clearwater® Hot Tub Chemical Starter Kit is a fantastic option for new inflatable hot tub owners and is an easy-to-understand introduction to the world of water treatment. Not balancing the Total Alkalinity levels in your hot tub can cause a number of issues that can impact your spa experience. ClearWater® is our chosen and recommended chemical provider. Developed with Lay-Z-Spa in mind, the range of ClearWater® hot tub chemicals includes everything needed to make sure your Lay-Z-Spa's water stays safe, clean and clear. Explore the table below which includes each product’s use and function.Never use unlabelled chemicals and please read the instructions before use. Avoid getting chemicals in eyes, on skin or on clothing. Avoid breathing vapours when opening a container. Avoid creation of dust. Never add water to the product. Always add product to large quantities of water. Use separate clean dry utensils for each chemical and clean after use. Do not add the product to any dispensing device containing residuals of other products. Drain pool to minimum mark and re-fill with fresh water to maximum mark, this will help to dilute the excess chemical.

Always pre-dissolve chemicals in a clean, plastic container in a well-ventilated area. When pre-dissolving chemicals always add chemicals to water and not vice versa. Always add the chemicals to the water. The Chemical Starter Kit includes 500g of ClearWater Chlorine Granules for disinfecting spas, 500g of pH Plus for increasing the PH of spa water, 700g pH Minus for decreasing PH of pool & spa water, 500ml Foam Remover to control & prevent foaming and 25 test strips to test for total alkalinity, chlorine and PH. Because pH measures how acidic or alkaline your water is, it is important to make sure your hot tub ph Levels are always balanced between 7.2 and 7.6 to avoid impacting your Lay-Z-Spa and your spa experience.

Never mix different chemicals in concentrated forms. This includes the kit products but also with other products like bleach or weedkillers – a dangerous reaction may occur. Dip a ClearWater® Test Strip in the centre of your Lay‑Z‑Spa, remove and hold it still for 15 seconds. Every attempt should be made to avoid mixing spilled material with other chemicals or debris when cleaning up. Do not attempt to reseal any contaminated drums. Do not transport wet or damp material. Around 60% of UK households are in hard or very hard water areas. To avoid scale build-up (which can impact water quality and pump components) use a weekly dose of ClearWater Scale & Stain Controller.

Remove cover from pool to allow evaporation of the chemical (keep the pool filter running constantly). Make sure that any outdoor storage of chemicals is as far away from your hot tub as possible and in a dry, covered area. Humidity or even small amounts of water can cause chemical reactions that could lead to dangerous fumes. Outdoor storage areas for your hot tub chemicals should be situated away from anything flammable. Keep any petrol-powered equipment, like your lawnmower, in a different location. The storage area should also be away from sources of heat, like an outdoor fire pit or BBQ. Clearwater Multifunction Tablets are an effective and hassle-free way of maintaining clear and healthy spa water. They contain a combination of chemicals that act in a number of ways. These slow-release tablets contain chlorine, algaecide and water clarifier. The chemical dispenser slowly releases the mini-tablets into the water, making this a completely hassle-free way of treating your water even for the user with a busy schedule.

Chemical Treatment Summary

This is an ideal set of hot tub chemicals for beginners as it comes with a guide with simple, easy-to-follow instructions, dosing guidance, safety tips and problem-solving so you can get confidently get started with hot tub water treatment and maintenance.

Total Alkalinity (TA) is the measure of your hot tub water’s ability to neutralise acids. Balanced Total Alkalinity helps control the pH levels and the correct level to aim for is between 80 and 120 parts per million (ppm).

The award-winning Bestway Clearwater Spa Starter Kit is a fantastic option for new inflatable hot tub owners and is an easy-to-understand introduction to the world of water treatment.