Makita DMR110 Li-ion DAB/DAB+ Job Site Radio - Batteries and Charger Not Included

Product Information

DAB display: station name, program type, multiplex name, time/date, frequency, bit rate/audio type and signal strength Press the Advanced setting button and rotate the Volume/Tuning Control/Select knob until "Manual Tune" shown on the display. Press the Volume/Tuning Control/Select knob to enter the manual tuning mode. Rotate the Volume/Tuning Control/Select knob to select the desired DAB channel. Press Volume/Tuning Control/Select knob to confirm the chosen frequency.

If your radio fails to work correctly, or some digits on the display are missing or incomplete, carry out the following procedure. SW Version" shown on the display. Press the Volume/ Tuning Control/Select knob to view the software version installed in the radio. If your device has version V4.3.17-1C02E installed, you can follow the steps and install the update. Press “Advanced” again and turn the volume control 2 times to the left and confirm the input at “Software Upgrade”.Press the Info button to cycle through the various options shown in the following letters (a. to g.). Press the Auto tune button and the radio will search and stop automatically when it finds a radio station. The radio will continue searching for the next available station unless the operator presses the Auto tune button to stop the scanning.

Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity. Reduced power, distortion and a "stuttering sound" are signs that the battery needs to be replaced. Batteries: 7.2v Cluster / 10.8v/12v Max CXT / 14.4v/18v LXT Li-Ion Batteries (Excluding Makita 'G' Batteries) Rotate the Volume/Tuning Control/Select knob until "Factory Reset" shown on the display. Press the Volume/Tuning Control/Select knob to enter the setting. To allow the radio to find the available stations, it is recommended to carry out a full scan of the entire DAB Band III frequencies.

Makita DMR110NW 18v LXT / 12v MAX CXT DAB+ Digital Job Site Radio White

Select the desired waveband by pressing the Band button. Make sure the soft bended rod antenna has been well placed for best FM reception. Try to avoid operating the radio next to a computer screen and other equipment which will cause interference to the radio. Once you have verified that you have a compatible operating system, follow this step-by-step guide: If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.

Rotate the Volume/Tuning Control/Select knob to scroll through the list of available stations. Press the knob to select the station.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Press and hold the desired Preset button until the preset number shown on the display, for example, "P2 Saved". The station is then stored in the selected Preset button.

Rotate the Volume/Tuning Control/Select knob to get the desired sound level. The LCD display will show sound level changes. Press the Advanced setting button and rotate the Volume/Tuning Control/Select knob until "Station List" is flashing on the screen. Press the Volume/Tuning Control/Select knob to enter the list of the stations. Frequency and channel Indicates the frequency and channel number for the currently tuned DAB station. From time to time, new DAB radio stations may become available. Or you may have moved to a different part of the country. In this case you may need to activate your radio to scan for new stations.Repeatedly press and release the Band button until "AU1" or "AU2" is displayed, then AUX function is activated. This radio has three tuning methods- Scan tuning, Manual tuning and Memory presets recall. Selecting a station - DAB Keep rotating the Volume/Tuning Control/Select knob until desired frequency is shown on the display. Press the Advanced setting button and rotate the Volume/Tuning Control/Select knob until "DRC Value" shown on the display. Then press the Volume/Tuning Control/Select knob to enter the setting. The display will show the current DRC value.