276°
Posted 20 hours ago

2 X Consumer Unit - Distribution Board Blanking Strip MCB Blanks (2 Pack)

£9.9£99Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

Yes, you have to ensure the supply tails enter the enclosure through an appropriate means to prevent damage to the insulation around the conductors. It is also important to tighten the tails that go into the incoming device within the consumer unit to the recommended torque settings, as set out by the manufacturer. Ensure the tails are fixed and secured so as to prevent disturbance. What coding is given to an existing plastic unit in good condition in an electrical inspection report? It is vital you know where your consumer unit (fuse box) is in your home in case of an emergency. What is inside a consumer unit? Even consumer units are now stylish! These flush boards are becoming the new trend. They install seamlessly into modern homes and are less bulky. The only difference here is the appearance, in terms of all the necessities (main switch, busbar) they are all the same. Garage Consumer Unit This is the most common consumer unit. These are metal and normally have a front lid hinged at the top, the size is completely dependent on the number of circuits you are having. (10 way, 14 way etc). Duplex Consumer Unit As to @The Happy Builder comments on being loose, that does not matter, we have an IP rating and not being able to be removed without tool.

No, there is no provision to use metal blanks. However, if they are supplied by the manufacturer of the consumer unit then they must be used. Can additional circuits be added onto an existing plastic style consumer unit? This type of board is anything under four ways… most of the time. They are commonly used in outhouses, sheds, and garages, where a couple of circuits may be required for lighting and tools. EV Consumer UnitSPD – Surge Protection Devices – They are now a requirement as part of the 18th edition regulations as it protects against surges into the electrics from outside the building. These are usually caused by lightning strikes, but can be caused by power surges from elsewhere down the electrical network. When this happens to your domestic fuse board it can be devastating to your home’s wiring. SPDs are installed between the outside feed and the main switch in your consumer unit and will trip if any inward surge is detected. These are the big boys – a consumer unit on top of a consumer unit! This type of board is usually supplied as a main switch option only but there are RCD options out there if you look hard enough. Duplex consumer units have become more and more popular since amendment changes in the last few years and because of the improved knowledge of circuit separation (RCBOs). Flush Consumer Unit

Unless you are a fully qualified electrician, then you should not under any circumstances try to replace your own consumer unit. It is a legal requirement that this type of electrical work is carried out by a certified professional. Beyond that, if done incorrectly, you could injure yourself and put both your family and home at risk. Yes, providing a risk assessment is carried out to say that, in the event of a fire, flames would not spread to the main dwelling. Carrying out a risk assessment is fundamental in this instance. Do fire retardant glands and trunking have to be used?Main Switch – The main switch controls the electrical supply in your home, and allows you to isolate all circuits by simply turning it on and off. Everything within your consumer unit is controlled by the main switch

Enclosure – This is the ‘box’ all of the relevant accessories are housed in. Since the introduction of the 18th edition, all new installations must be in a steel enclosure I think @rogerk101 is spot on with blanks, we are told type testing means we must only use what is recommended by the manufacturer, so if the blanks supplied by the manufacturer can be removed without a tool, then up to manufacturer to do a recall. All of the components within the consumer unit play a fundamental role in guaranteeing safety and integrity for each installation. No, providing the IP integrity after the installation is maintained, which is IP4X on the top and horizontal surfaces, and IP2XC everywhere else. However, the use of fire retardant glands and trunking is not precluded. Do intumescent pads and strips have to be used when installing a metal consumer unit?Dual RCD boards are supplied with a main switch and two RCDs. Consideration must be given to circuit design in this scenario. You should not, for example, put all the lighting circuits on the same RCD as if a fault ever occurs then the RCD will turn off the whole bank of MCBs it’s protecting. This will mean you will be in complete darkness whilst trying to resolve the issue. RCD incomer consumer unit Earth Bar – This is the common connection point for all circuits’ earth cables. All circuit protective conductors will connect on the earth bar along with earth bonding connections Neutral Bars – The common connection point for the neutral cables from the earth leakage protection devices (RCBOs)

These boards are predominantly used in garages and sheds. The big difference between this type of board and others is it doesn’t have a main switch. The main way to isolate this type of board is via a single RCD. High integrity consumer unit

How do the main types of consumer units vary?

Blanks – Blanks are pieces of plastic which clip to the din rail in just the same way as any circuit protection device and allow for future changes and additions to the circuit design. If you wanted to add a circuit for outdoor lighting for example – the consumer unit and busbar are ready to accept the MCB which would protect this circuit without any reconfiguration of the consumer unit

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment