Owatrol 1 Litre Net-Trol Wood Cleaner by OWatrol

Product Information

All other oils or sealers must be completely and thoroughly removed with Aquanett and stripped surfaces neutralised with Net-Trol, before applying Deks Olje D1. Previously coated surfaces (Paint, Stain, Varnish, Waterproofers) First, wet the surface with clean water, then apply Net-Trol with a synthetic brush or long pile roller and agitate the surface with the brush. Otros soportes: cemento oxidado, piedras con moho, plásticos polvorientos. Consejos para una aplicación correcta Apply the Net-Trol cleaner with a stiff nylon scrubbing brush working in to the rust stain. Then, leave it to work for 10-20 minutes. Step 3: Rinse and Scrub Remove any loose and flaking finish. Brush off any physical surface contamination e.g. moss, general dirt etc. Shake or stir product well before and during use including diluted solutions.

Do not allow Aquanett to dry on the surface. If drying occurs, dampen with a mist application of water. Always read the Deks Olje D1 Technical Data Sheet before using and follow the instructions carefully. Once removed, rinse thoroughly with lots of fresh clean water, using the highest pressure from the water source available or via the use a pressure washer at 500-1000 psi (35-70 bars). Shake or stir container well before use. Use neat or diluted. See data sheet. Work large areas in zones. Always work in the direction of the grain. Do Not use a wire brush. Remove Dilunett and dissolved paint with a stiff nylon scrubbing brush or paint scraper while flushing with water. The use of hot water makes this part of the job easier. Alternatively, you can use a pressure washer (max 60bars / 870psi).Scrub the surface with a stiff nylon scrubbing brush while flushing with water. To flush the water you can use a pressure washer (max. 60 bars / 870 psi), a garden hose or other water source.

Leave to stand for approx 10-20 minutes. If surface starts to dry dampen with a mist application of water Dilunett is our amazing solvent free paint and coatings remover. It is powerful enough to remove up to 8 previous coatings in just 1 application! It’s ideal for stripping large areas as Dilunett is non-flammable, does not dry out and remains active a long time. Then, whilst scrubbing the surface with a stiff brush, rinse the Net-Trol off the wood or alternatively, use a pressure washer (max 60bars / 870psi). If required, you can repeat the procedure.After stripping and rinsing, surfaces must immediately be treated with Net-Trol while still wet to neutralise the surface.

Can be used on most surfaces; on wood (some woods such as Oak and Chestnut require more attention before using Dilunett), metal (except Aluminum), plastic, stone, cement etc Recommended application: for best results surfaces must be clean, dry and free of loose dirt. Approximate Coverage Next, scrub the surface with a stiff nylon scrubbing brush again and rinse with large amounts of fresh clean water (you could use a pressure washer here to make your job easier if you have one). For particularly stubborn rust stains you may need to repeat this process again. It is safe to use on all exterior wood types and is also an excellent degreaser for use on tropical hardwoods to allow finishes like Deks Olje D1 to penetrate. Net-Trol can remove stains caused by tannin bleed and will remove all traces of weathering caused by mildew, pollution and UV rays. Why should I use Net-Trol? As Dilunett is biodegradable and non flammable, it is even safe to use in poorly ventilated or confined areas.

Recommendations for use

Allow to dry for 48 hours or until it meets the moisture content required by the chosen finish before finishing Access must be suitable for lorries which will be 3.5 tonne 7.5 tonne or 14 tonne lorries (7.5 tonne being similar to average refuse collection lorry) El limpiador NET-TROL para madera ha sido especialmente diseñado para restaurarla a su color original. Recupera la madera. Su fórmula eficiente, a base de agua y biodegradable, funciona muy rápidamente en solo 15 minutos.

The driver must have assistance to offload unless alternative arrangements made with our transport teamWet surface with fresh, clean water. Apply Owatrol Net-Trol. Scrub surface to agitate the Owatrol Net-Trol. Leave to stand for approx. 10-20 minutes. If surface starts to dry, dampen with a mist application of water. Scrub surface while flushing with water or use a pressure washer (max. 60 bar/870 psi). Rinse thoroughly with fresh clean water. If required repeat procedure. Exterior wood – weathered grey or dirty: Cedar, Larch, Pine (pressure treated or not), Teak, Iroko, Ipe, ... New wood surfaces have a hard shiny surface called mill glaze that prevents maximum penetration and bonding of any finish; sanding or treating the wood with Aquanett removes this, ensuring maximum performance of the finish. Weathered wood surfaces (untreated)