Kreg KJDECKSYS20 Deck Jig

Product Information

To ensure the highest quality, our Balau has waxed ends to prevent splitting and is kiln-dried - a critical step that sets our product apart from sub-standard alternatives. The STANLEY Tylon tapes comply with European class II standards. This means the maximum permissible tolerance over 3 metres is less than a millimetre. Kreg is much easier to work with when it comes to unscrewing. Since it is an open system, the screws are easier to undo so you won’t have much trouble. During the winter, when the humidity is significantly lower, the wood will dry out and reduce in size. You might have noticed this quality if you live in an older home that has solid wood doors. A door that might work just fine in the winter may in the summer swell and not close properly in its door frame. With your spacer in place, pull the handle of the chisel to you to bring the board tight against the spacer. Then use your other hand to drive in the screw or nail.

Deck Jig KJDECKSYS20 - The Home Depot Kreg Deck Jig KJDECKSYS20 - The Home Depot

We aim to supply the best products possible. Please be aware of other outlets selling 'Sub-Standard' Balau! Where your measurement falls on the boundary of two sizes, we recommend selecting the larger of the two sizes for a comfortable fit. They’re similar but their screwing systems, spacers, and ease of replacement make them different from each other. The jig itself has an easy-grip handle that gives you a secure hold and complete control over each and every joint.

Talk to us

The tool automatically creates 3/16-inch spacing. The cool thing about this tool is that it allows you to get exact spacing while at the same time installing your fasteners, saving you a significant amount of time.

Camo Deck Screws and Tools – Deck Supermarket Camo Deck Screws and Tools – Deck Supermarket

Timber is a natural product and is subject to continual movement when exposed to atmospheric conditions. This may be evident with splits, shakes, knots or warping. These are not considered to be a fault or defect. Please allow a small percentage for waste. The Tylon coated blades are up to 1.5 times more resistant to abrasion than normal standard lacquered blades, giving improved longer tool life. Camo is pretty much professional level. It is made for professional people who carry more tools but need something efficient. So if you’re a beginner, don’t reach for the Camo tool. You can usually tell how “wet” treated wood is by its green color. Wet wood takes time to season. Over months, treated wood will dry out and contract. You need to take this into account when determining your spacing. The Tiger Claw TC-G Hidden Fastener system by FastenMaster is ACQ-compliant and compatible with grooved boards including Trex, Fiberon, Wolf, Veranda, Brazilian Redwood, Ipe, Ironwood, Teak, Cambara, and more.With a razor-sharp cut point and ground, serrated lower thread, these screws will not split or splinter the wood even when used at the board's edge. Don’t despair! There is a solution here. You’re not the first one to make this mistake and you certainly won’t be the last. The folks at Lounsbury Products LLC know this, and they’ve designed The Saw Guide to help you.

Deck Tool for Edge Fastening CAMO Marksman Pro-X1, Deck Tool for Edge Fastening

A 1/8” gap can easily be accomplished through the use of an 8d nail. Lay the boards in place, using several 8d nails as spacers. While pushing the board flush against the spacers, secure the board into place with your choice of fastener. This makes the wood less susceptible to cupping, warping, expanding and contracting that wet wood typically undergoes. This means KDAT can be installed with a 1/8-inch gap. It should be noted that KDAT does need to be immediately stained and sealed after installation to protect it from the sun. Please Note: We recommend that you keep your Balau dry and away from moisture until it is time to lay it, as timber is a natural product and is subject to continual movement when exposed to atmospheric conditions. This may be evident with splits, shakes or warping. These are not considered to be a fault or defect. Please allow a small percentage for waste.Since 1843, Stanley has been delivering hardworking, innovative and powerful tools that tradespeople can trust and to help Pro’s get the job done better. While nails are good spacer options, they can also be difficult to work with. Nails can easily slip out of your fingers or between the boards and onto the earth below.

Deck Board Spacing: Last Guide You’ll Ever Need Proper Deck Board Spacing: Last Guide You’ll Ever Need

And the best part is, this tool won’t cost you much more than lunch at your favorite fast food joint. You’ll also want to take into account the type and intervals of your fasteners. Fasteners are what hold boards in place, resisting their efforts to bend and move as the humidity changes.

Your Basket

But the scenario is different in long term. Camo jigs are harder to replace and unfortunately, they start creaking pretty early. So if you want something long-term-friendly, go for the Kreg one. To select the correct glove size, simply measure across your palm at the point indicated in the last picture on this listing. Then compare your measurement with the chart below to ensure you select the correct glove size for your hand.