Joined in 2023 
82 
63 About this deal
It is obvious that the printer, due to its design, is quite high at 101cm including the filament spool, but with a triangular base of 46cm edge length it occupies not much space on your workbench. The heavy stepper motor of the Bowden extruder is also located on top of the device and therefore does not have to be moved when printing. It was not very well known in Europe until now, but it is gradually starting to make a name for itself thanks to its Delta type 3D printers, which it has made its speciality!
If you have the power button on the front left of the screen, you have a QQ (8-bit) unit, which is different firmware. Reddit and its partners use cookies and similar technologies to provide you with a better experience.There is a lot of tutorial videos out there that are worth watching to understand how to operate it to its best. Bit Motherboard - QQ-S PRO is equipped with a 32-Bit motherboard and a separate MOS module, allowing for stable prints even at high printing speed.
Thus, especially at the beginning and at the end of the individual extrusions of the Anycubic PLA filament, you can see that it takes some time until a stable filament flow is achieved. My personal opinion on this is: It's better to have good brass bushings (and the ones on the QQ-S are good) than bad linear ball bearings (I've had quite a few of them)!The printer is from a secondhand reseller he changed the belt and the printing block, updated to mks 2. To make your sale worth, we can give 100% assurance that we assist you to choose right 3D printers to meet your requirements.
Energy consumption and noise emissions are at an acceptable level ex-factory, but at least in terms of volume, strong improvements could be achieved with better stepper motor drivers and quieter fans. From March 28th to May 9th, the pre-sale of SR printer has officially ended, thanks to the support of 3D printing users to FLSUN and SR printer. According to the printer menu, the mainboard identifies itself to be a MKS Robin Mini Board and the microprocessor type STM32F runs the Marlin firmware. No BL Touch on this Delta, it is indeed a specific sensor that you have to remove once the plate adjustment is done, it is not necessary to put the sensor back at each print, for my different print tests, I didn’t need to do it again, and I was able to make about 10 prints without any problem.status":"1","isDefault":"1","createDate":"2021-08-20 13:55:41","updateDate":"2021-08-20 13:55:41","productSkuSpecs":[],"moq":1,"skuId":0,"chargedWeight":13. This manifests itself in jerks and later also in large holes in the walls, since the filament flow is not stable when the firmware repeatedly stops the movements of all motors briefly. Our platform features an extensive roster of the industry's leading 3D printer manufacturers, ensuring that you have access to the most up-to-date and sought-after machines tailored to your specific requirements. Due to their length, the cables could get in the way of the axle slides and be damaged by friction or pinching.
This is a mechanical switch, which must be attached to the print head via a magnet before starting the procedure. Already from 80 mm/s onwards, the firmware apparently no longer keeps up with the calculation of the movements. I usually use the Prusa Slicer, and it’s a good thing Prusa recently added the Delta machines from FLSUN! It’s been a while since I last tested this type of machine (for almost 3 years), and I hadn’t yet had the opportunity to try this brand of which I had read quite good reviews.
The Voltcraft SL-10 sound level meter still shows a maximum volume of around 60 dBA even at a distance of one meter (~3. After a 30 minute assembly following the maker's included video and instructions, the machine was constructed and powered on. Once assembled the machine seems quite stable, and the components of good quality, the belt tensioning system (the little knobs on top of the machine) are quite practical. Here, there is a simple solution with tape or a somewhat more elegant solution with a few printed parts.
Great Deal 
New Comment