Washing Machine / Dishwasher "Y" Piece Hose Splitter

Product Information

This doesn’t mean you have admitted defeat, just that you are looking for extra guidance. You may even learn from watching. If you are ready to speak to a professional, please use our handy free search feature to be connected to qualified plumbers in your area. To make sure you get a good seal between the connector and pipe, clean the area of pipe with steel wool and remove any paint. Step 2 The problem is the splitter is still leaking, its much better, not spraying water out but its still dripping quite a lot. Does anyone have any suggestions as to what I'm doing wrong here? Should I just try tightening it a bit more with pliers? I know washing machine hoses should be hand tightened as over tightening makes them leak but I am very tempted to just to tighten it another few mm, would you advise this or is there a better option? Many people are unsure how to connect a washing machine waste pipe to a sink, but it actually isn’t too difficult. Plus, you get the added benefit of the grey water from your washer helping to eliminate grease and debris from your sink waste pipe. A drain hose funnels the waste from your washing machine into the ground. So, when fitting a new washing machine, it is a good idea to learn how to install a washing machine drain hose.

Make sure the valve is in the ‘off’ position, then screw it into the saddle by hand – you’ll feel it cut into the pipe as you do so. Keep turning the valve until its body is at right-angles to the pipe – this will let you turn it on and off easily. Step 5 Push-fit plastic compression waste pipes have many advantages including their ability to join old pipes to new and are easy to fit and adjust. And if a connection fails, they are simple to remove and refit with a new one, avoiding cutting pipes and solvent welding. If you already have a washing machine plumbed in and want to get a dishwasher too, you’ll want to know if you can use both appliances at the same time – and if you can buy longer hoses and run them under the kitchen cupboards. A dishwasher normally just has a cold water supply. The mini stop valve that connects the supply pipe to the machine’s hose lets you isolate the machine without turning off your water. Connect the waste hose to a washing machine trap beneath the sink or use a standpipe with a P-trap. Top tipMany of us rely on our kitchen appliances on a daily basis to save us the time and energy of doing things manually, particularly our dishwashers and washing machines. Each will need a water supply, an electricity supply and a waste pipe. So, learning how to connect a dishwasher and washing machine to one waste pipe helps keeps things simple and efficient.

If the hoses won’t reach the existing supply pipes, you’ll need to add fittings as described below and run branch pipes to the machines. These should end with mini stop-valves to which the hoses can be connected. Typically, the appliance will be supplied with fixing screws that go through the carcass from the inside to the worktop above and the cabinet sides. The appliance will stand directly onto the floor so adjust the legs to raise the appliance to the correct position and fix in place. If you’re attaching a plinth across the base of your cabinets, you may need to cut a groove in the top edge to allow the correct door opening. Fixing the decorative door You may need to unscrew the hose from the U-bend under the sink, remembering that this is likely to disconnect your sink waste temporarily too. Consider putting the plug hole stopper in to prevent people from using the sink in the meantime. This is the simpler option and ultimately the option that I myself chose. You connect your two waste pipes to one which then feeds into the waste trap. I chose this simply because I cannot be arsed messing around with the U-bend under the sink.

More Reading

Firstly, isolate any incoming power to the washing machine. (This may involve unplugging the washing machine or turning off the power supply to your home if the machine is wired in.) So I got one from screfix and fitted it as tight as I could with just my hands and straight away it leaked from behind the nut so I used some pliers to tighten it a tiny bit, this seemed to stop the leak so I tried the dishwasher however once it started to draw the water out the water started spraying out. So I tightened it more and more with the pliers and it still wouldn't stop. Eventually I tightened it that much the plastic end broke off. Yes, I have been running my dishwasher and washing machine off the same waste pipe for over a year now with no problems. It has been used with both machines operating at the same time and again there were no problems. How do you connect a dishwasher to a waste pipe?

So like I said earlier you have two main options, I will talk through the pros and cons of both of these below. Washing machine trap with double spigot Read on to discover useful tips with sections focusing on how to connect a washing machine waste pipe and how to extend a washing machine drain hose. Connection types for dishwashers and washing machines Double-spigot trap: Your waste is likely to leave your property through a ‘U bend’ similar to that on your toilet and beneath a sink. This will comprise a piece of vertical pipework, leading to a ‘U bend’ or trap. Double spigot traps are available, where the vertical piece of pipework is replaced with one that allows two connections, or spigots, into it – one being your dishwasher, the other, your washing machine.Installing waste pipes for washing machines and dishwashers can be done quite simply, but extra-long hoses tend to sag and let stale waster stand in them. See how to connect dishwasher and washing machine to one waste pipe here… Setting Up Also, as with all combined drainage systems, cleaner water can help clear the drains of any dirty water. In this case, the ‘grey water’ from your washing machine will help flush out any greases and fats that find their way into your dishwasher waste. I've got 1 hot and 1 cold inlet available and the washing machine needs 1 of each however I've recently bought a dishwasher and need to plumb it into the same cold water supply.

Finally, pull the drain below the level of where the water is sat – this will likely have a siphon effect that will start to clear the water. Usually, a washing machine has hot and cold water pipes extended with T-fittings to reach its supply hoses. Mini stop valves allow you to isolate the machine without having to cut off the water supply. Hook the waste hose into a standpipe with a P-trap. In fairness, this isn’t a hugely difficult job and if you are even remotely DIY competent you will be able to fit one. However, it can be dirty, depending on how old your existing U bend is it may well be full of slimly, foul-smelling gunk.If the supply pipes run close to the machine, you can simply fit the stop valves and screw the hoses to them. An alternative is to fit self-cutting connectors which contain isolating valves that can be installed without draining the pipes. Pipe Connections Place your dishwasher on a firm, level floor close to an outside wall if possible. This appliance will need a water supply and waste pipe just like your washing machine. Your washing machine is normally connected to both hot and cold water systems – the dishwasher usually only needs a cold water supply. Every washing machine is different and drain hoses are available in a number of sizes online or at plumbing merchants. That is why when buying a new washer or moving an old washer, you may need to learn how to extend a washing machine drain hose. Splitter: The easier option, however, is where you leave your existing waste in place and connect the two wastes to a ‘splitter’. This acts in a similar way to the double-spigot trap but requires less plumbing expertise and might not prove as dirty a task. A washing machine and dishwasher splitter is a Y or T piece shaped device that allows two appliances to be connected to one outlet. They come in a range of materials including plastic and brass.